Category Archives: Bunta’s Initial B

This time I made SSB for Yamaha RZ 250 R. This vehicle is considerably rare car by saying that this vehicle is more than 30 years old. Of course it will not quite get parts etc, so I would like to protect as much as possible with SSB. Since the structure of this vehicle at […]

This time I made SSB for Kawasaki’s new Z1000. By saying the same frame as Ninja 1000, it may be possible to use the same type of SSB? I thought, but I made a new work saying that I would make a solid one. As for the production, the position of the mounting hardware of […]

This time I made SSB for the new Z250 of Kawasaki. In this type, the engine is suspended from the vehicle and the frame, basically a bolt with high strength It was attached to the upper side and there was no bolt attached to the lower side at all. On top of that there was […]

This time I made SSB for Yamaha VMAX 1700 of ultra heavyweight. As the machine weighs about 320 ?, not only the strength, but also the energy applied to the car body Taking into account the big thing, I made it possible to distribute the energy to 4 places as much as possible. Designed with […]

This time the SSB for Honda RVF 400 was renewed. Last time we did not make jigs but made it as one-off production In this time I made another work and made jigs. In the future you can produce without having to bring in the vehicle. We cleared the fall test successfully! http://zrx-drz.at.webry.info/201412/article_1.html

This time I made SSB for CB 650 F which was released as a new book. I think that it can be installed in CBR650R because it is said to be the same frame. This machine was a difficult car that the frame was tilted and there was no gap between the engine and the […]

I am producing the MT 07 now Since it turns out that the steering wheel is overrun when the actual running is repeated I made a handle stopper base to adjust the steering wheel turning angle. With this specification, since the steering wheel turning angle never changes Once you have adjusted it you can continue […]

I will enter a new model MT 07 in the last time in Chubu Dunlop ~ Because it wrote, it is a short time, but also breaks in Finally I entered the machine production. What we are newly producing is Idle adjuster kit And a rigid handle post kit to make the rubber mount of […]

This time I made SSB for SUPER DUKE 990 of KTM. I think that a secure SSB has been completed though it is a narrow installation space. Clear the fall test successfully! I was concerned that the protruding clutch housing also protected without grounding. How is it? http://zrx-drz.at.webry.info/201409/article_2.html

I am enjoying a big bike gymkana with ZRX 1200 this season. After all the big bike gymkhana is attractive and cool! I think so, I thought it was no mistake. However, the depression of physical strength and physical ability that I thought was no longer better than planned Because it is few, I started […]

This time I made SSB and rear slider for Honda's CB 1000 R. Basically it is the same structure as the Hornet 600. This CB 1000 R has a radiator sub tank between the shroud and the frame Production could not be done as it was in close contact with the frame. So, how to […]

This time I made a SSB and a rear slider for MT 07 just out of Yamaha. It is very easy to make so that the items with both strength and design are satisfactory. The fall test was also sufficiently cleared. 07, basically the rear slider does not ground. As the effect comes out, it […]

This time I made SSB for Honda CBR 1100 xx Super Black Bird. Like the Kawasaki ZX 9R we made last time, I wanted to add SSB to the place I wanted to add an engine hanger etc. Because of the structure without bolt holes and structures, by having the same structure as 9R We […]

This time I made SSB for Kawasaki ZX9R. This vehicle is a perfect hanging type frame, where you want to put a bumper There was no bolt or strength member, invented a new type and made it. On the frame surface, install it so that the force is dispersed with a thick plate, and the […]

This time I made a caliper bolt for MT09! It is a front caliper of MT 09 which uses very normal bolt I tried to make bolts to think that I would dress up a little more. In the world, there are places where stainless steel bolts are used for caliper bolts Yes, but actually […]

This time I made type 2 SSB for Kawasaki ZX10R. Last time it was an SSB that was premised on wearing a cowl This time SSB will be premised to remove the cowl. However, it may be possible to install the cowl depending on the processing of the cowl. The thing of this time is […]